Organic silicon coatings have very low surface tension and excellent waterproof performance. In addition, their superior cold resistance, heat resistance, elasticity, and weather resistance make them widely used as waterproof and moisture-proof coatings, especially for building and material waterproofing, with very satisfactory results.Moisture intrusion is the main cause of damage to concrete and masonry buildings. In order to extend the service life of buildings, it is best to use a waterproof ...

In the construction of large formwork, the selection of release agent is very important, which directly affects the construction progress and concrete quality. In the past, sodium alginate and engine oil emulsion were used as release agents, and although the effect was good, they needed to be coated once every time the concrete was poured, which was labor-intensive and time-consuming, and could not be used on rainy days. Using methyl silicone resin, the demolding effect is good, the wall surface ...

Product Name: Release AgentItem No.: SilibaseRA-4888FeaturesSilibaseRA-4888 release agent is an efficient release agent.Environmental health harmless to human body without bad smell.Non-stick mold, excellent release properties and higher release times.Improve productivity: Protect the mold from carbon deposition, more than 10,000 release times without white residues and less to clean the mold.Product surface is easy to clean, does not affect any after-processing such as painting, varnishing and ...

The Mid-Autumn Festival symbolizes the reunion of people with the full moon. In order to express our yearning for our hometown and relatives, we hope for harvest and happiness and become a rich, colorful and precious cultural heritage. Since ancient times, Mid-Autumn Festival has many folk customs, such as offering sacrifices to the moon, appreciating the moon, eating moon cakes, playing with lanterns, appreciating osmanthus flowers, drinking osmanthus wine, etc.In accordance with the spirit of ...

Anti stick release coatingSince the emergence of organosilicon polymers, people have found that they have many special properties, especially as release agents, such as silicone resin, silicone oil, and silicone rubber, which can all be used as release agents. The choice of material as a release agent in use mainly depends on its economy, service life, and ease of application.The anti sticking and demoulding properties of silicone resin are similar to silicone oil and silicone oil lotion. It has ...

The main characteristics of silicone glass resin are hardness and transparency, with a visible light transmittance of over 90%. The film insulation performance after film formation is good, and it has the advantages of friction resistance, heat resistance, aging resistance, radiation resistance, low temperature non brittleness, solvent resistance, hydrophobicity, moisture resistance, non toxicity, and strong transmittance. There is no gas release during use, even under 450 ° C, high vacuum, and ...

Due to the small value of R: Si in glass resin (equal to or slightly greater than 1), high functionality, and small steric hindrance of methyl groups, the C2 pressure O-group is easily hydrolyzed, and the HO base is easily shrunk into a bulk structure. Therefore, this resin has the characteristics of low-temperature rapid curing and good film-forming properties. If a small amount of drying agent is added, the resin can be cured into a film within a few minutes at 50-60 ° C; Even without the add ...

Product Name: Acrylic DispersionItem No.: SilibaseSRR-3170IntroductionPolyurethane acrylate lotionProduct AdvantagesGood stain resistanceGood dispersibility of matte powderSmooth and delicate to the touchTechnical DataViscosity (cP/25℃): 100-1500solid content: 53%Appearance: Milky white liquidbase material:water:103.7°oleic acid:53°CharacterizationGood stain resistance, high hardness, good wettability, and good versatilityBase Material and ApplicationBase MaterialApplicationPCPC+ABSABSAnti bi ...

Product Name: Cutting FluidItem No.: SilibaseCFZ-1001Product DescriptionThe fully synthetic cutting fluid is suitable for grinding and heavy-duty cutting of ferrous metals, aluminum alloys, copper, and stainless steel, fully meeting the requirements of high-speed feeding and operation in today's mechanical operations.The fully synthetic cutting fluid replaces traditional cutting oil and is widely used in harsh machining applications such as gun drills, hobbing, and reaming due to its superior pe ...

Product Name: Silicone MasterbatchItem No.: SilibaseMB-TPE7950Material properties:No.Testing itemstest methodresult1Melt index (g/10min) (210 ℃ * 5kg)ASTM D123826 ±52Tensile strength (MPa)ASTM D63873Tensile elongation at break (%)ASTM D638>6004Hardness (Shore A)ASTM D2240505Density (g/cm ³)ASTM D15050.890±0.03Product Features:Due to the presence of a large number of silicone rubber particles in the elastomer after alloying, the alloy elastomer is endowed with a perfect tactile sensation o ...